Sunday, October 20, 2013

Limiting Suction Outlet Plumbing Velocities


Standards Mandate the MAXIMUM SPEED LIMIT
 
Standards dictate that the MAXIMUM velocity limit in the plumbing at the suction outlets is 6 feet-per-second (ANSI/APSP-7).  I recommend that the maximum designed velocity on the suction side of the pump be limited to 4 feet-per-second.

Why lower that the maximum?  In suction lines speed is not a good thing.  In fact, excessive speed causes equipment wear, friction, lost energy and pump noise.

Since pump selection is the last task performed when designing a suction system, oftentimes there is not a pump curve that EXACTLY fits the system requirements.  By designing below the maximum allowed velocity, the designer has the ability to select the closest pump curve, even if it slightly exceeds the 4 FPS design - safely remaining below the maximum.

Isolation Valves 

When isolation valves are placed in suction lines between a pump and the suction outlets, any singular suction line supplying water to the pump MUST be capable of providing 100% of the systems’ designed flow rate at a maximum line velocity of 4.5 FPS.  

This is required, because if valves are closed and lines are improperly isolated, and if the pipes are not of sufficient diameter, the line velocity would quickly exceed the 6 FPS standard.

Energy Efficiency


Energy efficiency is greatly enhanced by lowering the line velocity.  Cavitation, operating noises & suction entrapment hazards are also reduced by lowering the line velocity.

Line velocities cannot be reduced much lower than 4 FPS, otherwise pipe scour would not occur.  Debris and sediment could eventually collect in the pipes.

Paolo Benedetti, SWD Aquatic Artist, Watershape Consultant, Expert Witness, International Construction Management 
Contact the author at: info@aquatictechnology.com or 408-776-8220 
"Creating water as art."™ 
Aquatic Technology Pool and Spa© 
©www.aquatictechnology.com All rights reserved.

Thursday, October 10, 2013

Salt Water Pools Galvanic Corrosion

The current rave is have a "salt water" pool.  Many owners are under the false impression that these pools are "chlorine free."  Though, this is hardly the case.

Electrolytic Solution

Salt is placed into the pool to create a solution much weaker than that found in the ocean.  In fact there should only be about 3,000 ppm of salt present in a salt water pool.  A special device at the equipment pad, then splits the sodium chloride (salt) into CHLORINE!  These owners are merely using the salt to generate chlorine in their pipes!

But placing salt into the pool also turns the pool water into a electrolytic solution.  Add some stray current and the pool becomes in effect a giant electroplating tank.

A salt water pool is really a very weak, but giant battery!

Galvanic Corrosion

These stray currents will cause staining of the plaster surfaces, galvanic corrosion of less noble metals.  Copper heat exchangers will actually dissolve from the inside and decay on the outside, as their molecular structure is attacked.  Metals suspended in the pool water will bond to more noble metals, plating them in unusual colors.

Sacrificial Anode

Many in the pool industry have drawn on "a solution" that boat owners have used for years - SACRIFICIAL ANODES.  HOWEVER, a SACRIFICIAL ANODE is not the placebo everyone is seeking. 

On a boat, a sailor does not care if the anode erodes, or if the anode's metals dissolve into the water (ocean).  The anode on a boat is a lot cheaper than the wiring, an expensive bronze prop or brass components.  It prevents the corrosion of the boat's precious components, by SACRIFICING itself instead. 

Placing a sacrificial anode in a swimming pool is doing the same thing as on a boat.  One is merely offering a SACRIFICIAL metal for the galvanic corrosion to attack, instead of the precious components.  It does nothing to address the actual cause - GALVANIC CORROSION.

So instead of plating surfaces with copper, you will be plating them with zinc or magnesium from the sacrificial anode.  The sacrificial anode will save the copper, but it will not stop the staining or plating of the stainless steel components.  That will now occur with the metal from the anode.  


This is exactly why anodes need to be periodically replaced - they are sacrificed.  And where those sacrificed metals go is out of your control!

The Source of Stray Current


The equipotential bonding grid does not prevent galvanic corrosion.  In fact, if there is stray voltage finding it's way to the pool through the property's CONTINUOUS GROUNDING SYSTEM, the equipotential bonding grid may actually be feeding voltage to the pool's metallic components. 

The bonding grid can actually function as either the electrode or cathode, depending if there is stray voltage present or if it is providing a path to ground (where the equipotential bonding grid and the grounding grids are cross connected - pumps, heater's, panel boards, etc).

For these very reasons, many pool builders that I know and I, have ceased installing salt systems.  We now promote "off-line" on-site generation of liquid chlorine from salt or tanks of liquid chlorine and then the controlled dispensing via a ORP/pH Controller.



Paolo Benedetti, SWD Aquatic Artist, Watershape Consultant, Expert Witness, International Construction Management 
Contact the author at: info@aquatictechnology.com or 408-776-8220 
"Creating water as art."™ 
Aquatic Technology Pool and Spa© 
©www.aquatictechnology.com 
All rights reserved.

Monday, September 9, 2013

Aqua Design International Projects

Aqua designs for international projects require specialized training and knowledge.

International Codes

Many international locations have few, if any, aqua design codes or standards.  So what codes should apply?

In this litigious society we live in, designers should do their best to comply with the most stringent published code.  Most of those codes reside right here in the United States.  The leader for commercial pool standards is the State of California.

Avoiding Litigation

If the designer is based in the United States, a reasonable line of legal questioning in foreign litigation would be:

"Are you trained to design and build projects that are compliant with the more stringent US codes and standards?"
"In the absence of local regulations or building codes, wouldn't it be prudent to design and build to those same margins of safety?"
"So, by not designing to those same US standards, you are saying that a life in this foreign country is worth less than a life in the US?"

Keep in mind that in many foreign countries, errors and omissions are often construed as criminal negligence.  A designer may not just be trying to avoid financial losses, but jail as well.

Bottom Line

When designing foreign projects, it is best to design a project to be in compliance with the most stringent standards or codes that exist, unless they are in direct conflict with a local regulation.

The standards established by the ADA, IBC, NEC, ISPSC, APSP, NSF, ACI, TCNA, ANSI and VGBSA may not be the adopted code in a foreign locale.  However, these standards were established for a reason - life safety and user convenience.  

Don't the people in foreign countries deserve the same levels of protection?


Paolo Benedetti, SWD - Aquatic Artist, Watershape Consultant, Expert Witness, International Aquatic Designer and Builder
Contact the author at: info@aquatictechnology.com or 408-776-8220 
"Creating water as art."™ 
Aquatic Technology Pool and Spa©
©www.aquatictechnology.com All rights reserved.

Wednesday, September 4, 2013

Full-Time Swimming Pool Expert Witness

Should you hire a full-time swimming pool expert witness or someone who is still active in the business who is a part-time expert witness?

Out of Touch

That's a rather straight forward question with an obvious answer.  A "professional" expert witness has retired from the business.  They spend all of their time examining projects, writing reports and providing testimony.

So how do they stay up to date with the current trends in the industry?
How do they learn about the innovations in construction techniques?
Where do they get exposed to the new products that make past technologies obsolete?
When did they last actually build something utilizing state of the art methods?
What was the last project that they actually designed or engineered?
How do they stay up to date on the newest codes, industry standards and acceptable trade practices?

The longer they have been a full-time expert witness, the longer they have been out of touch with the industry.  Though they may be able to stay up to date on the broad scope of changes, the nuances of change pass them by.

In-Touch

Those that are part-time expert witnesses, usually have full-time jobs actually designing, consulting, managing or constructing swimming pools.

Because they are active in the industry, they are current on all of the standards, codes and acceptable trade practices.  Because they are on the leading edge of design innovation, they are up to date with the technological changes and techniques required to execute these new designs.

The expert witness you need to hire, is one who is still practicing in the industry.  Someone who is out in the trenches, resolving design issues and building projects on a daily basis.


Contact the author at: info@aquatictechnology.com or 408-776-8220 
Paolo Benedetti Aquatic Artist, Watershape Consultant, Expert Witness 
"Creating water as art."™ 
Aquatic Technology Pool and Spa 
©www.aquatictechnology.com All rights reserved.

Wednesday, August 14, 2013

Expert witness swimming pools ADA Compliance

Expert witness discovers that "ADA Compliant" products are not always ADA compliant.

Don't take their word for it...

While designing a project for a disabled Veteran, I was asked to specify an outdoor shower for use after workouts, laboring in the yard and swimming.

I began to research outdoor showers and discovered that there are many models that are labeled "ADA Compliant."  I downloaded the specifications and sat back with an cold glass of iced tea for some rather boring reading.

Being familiar with the ADA codes, I soon realized that almost every one of these outdoor shower products were falsely advertized as being "ADA Compliant."  They in fact, were only partially complaint.

Know the codes

The outdoor showers were only partially ADA Compliant.... they merely had ADA Compliant handles on the water valves and lower shower heads.  Convenient yes, but they had omitted a major safety factor.

Temperature modulation and temperature limits are a mandatory feature of ADA Compliant showers.  If a shower gets scalding hot, a disabled person cannot jump out of the water and scream, "OH, $%&#  !"  Someone who is paralyzed might not even feel the burning water.

Liability

If you are selecting products for a project, it is imperative that you know the codes that apply to those products.  Simply relying upon a manufacturer's label of ADA Compliance can result in the specifier or installer assuming a lot of liability in the even someone is injured.

It helps to know the codes!

Paolo Benedetti Aquatic Artist, Watershape Consultant, Expert Witness 
"Creating water as art."™ 
Aquatic Technology Pool and Spa ©www.aquatictechnology.com

Monday, August 12, 2013

Soils Reports and Project Structural Engineering are the law

Swimming pool expert witness explains why soils reports and project specific structural engineering are required by law (the building codes).

Structural Engineering 


Swimming pools must be designed to withstand any force that will be exerted upon the structure.  These forces are called "surcharges."  The leading surcharge on an in-ground pool are the soils surrounding the pool itself.

Soils

The soils must be able to support the structure and prevent movement.  Soil conditions can very from lot to lot in the same subdivision.

For example, these soils can be expansive, non-supportive, prone to sliding or vertical uplift or subject to liquifaction.

One cannot ascertain the characteristics of the underlying soils by looking at the top soil.  That is unless they are Superman with x-ray vision.

Structural Engineer needs a soils report

A structural engineer cannot design the structure, without knowing the characteristics of the underlying soils.

Therefore, they need a soils report to tell them what site conditions are present.

Required by Law (Building Codes)

The 2012 International Swimming Pool and Spa Code states:
802.1 Materials of components and accessories.
The materials of components and accessories used for permanent inground residential swimming pools shall be suitable for the environment in which they are installed. The materials shall be capable of fulfilling the design, installation and the intended use requirements in the International Residential Code.
802.2 Structural design.

The structural design and materials shall be in accordance with the International Residential Code.  


The International Residential Code goes into further depth as to the requirement for project specific engineering, soils reports, minimum concrete strengths, foundation requirements, shotcrete strengths, rebar installation, special inspectors, laboratory testing, etc.

Since the 2012 International Swimming Pool and Spa Code has been incorporated into the International Building Code, which is THE building code for the entire United States... it has defacto become the swimming pool code for the United States.  

The Swimming Pool Code's counter reference to the IBC and IRC places a lot of additional minimum specifications and requirements on the construction of a concrete swimming pool or spa (gunite/shotcrete).

It helps to know the law.


Paolo Benedetti 
Aquatic Artist, Watershape Consultant, Expert Witness 
"Creating water as art."™ 
Aquatic Technology Pool and Spa ©www.aquatictechnology.com

Thursday, August 1, 2013

Swimming Pool Concrete Compressive Strengths

http://aquatictechnology.com/pool-designer-services.htm

Some expert witnesses are confused by the terms "permeable" & "waterproof" as they relate to concrete.

Waterproof VS Permeability

Increased concrete densities provide for stronger structures, for which I am an advocate.  However, increased densities ONLY REDUCE concrete's permeability, they DO NOT render it impermeable (waterproof).

Experts need to stop claiming that higher psi concrete's are WATERPROOF - THEY ARE NOT !  Yes, they ARE less permeable, but water will still weep through the concrete - just at a slower rate.

None of the following references (all in my personal library) state that higher density concretes are waterproof:

Building Code Requirements for Structural Concrete (ACI 318M-08)
Steel Reinforced Concrete Structures, Mohamed A. El-Reedy (2008)
Reinforced Concrete Designers Handbook, 10th Ed Reynold & Steedman
Engineering Concrete Mix Designs & Test Methods, Irving, 1999
Advanced Concrete Technology Vol. #1 Constituent Materials, Newman & Choo, 2003
Advanced Concrete Technology Vol. #3 Processes, Newman & Choo, 2003
Advanced Concrete Technology Vol. #4 Testing & Quality, Newman & Choo, 2003
ACI 201.2R-01 Guide to Durable Concrete
Reinforced Concrete Design Theory & Examples, Macginley, 2003
Masonry and Concrete for Residential Construction, Beall, 2004
ASTM Steel Handbook, 3rd Ed, Bringas, 2002
Reinforcement for Concrete — Materials & Applications, ACI Educational Bulletin #2, 2006
ACI 506R - Guide to Shotcrete


Other Standards REQUIRE additional protection

Though one may be comfortable with the low permeability of 9,000 psi concrete, other trade standards specify the use of waterproof membranes (e.g. TCNA, CTIOA).   Ignoring these other standards is as egregious as shooting a 2,500 psi pool shell!


Both TCNA and CTIOA require additional waterproofing measures under tile in vessels, tubs, showers, etc.  Until those standards are repealed or modified, one cannot simply chose to ignore them.

Special Protections

The mere use of high density concrete does not provide protection from hydrogen sulfide or chloride corrosion of the concrete.


Protection from these ravages of nature can only be provided with special mix designs, concretes, admixtures and/or waterproof membranes.

The currently accepted ACI permeability tests have inherent flaws.  The chloride ion penetration test (ASTM C1202) does not measure how rapidly the ions penetrate the concrete.  Nor does the test account for variations in hydrostatic pressures, a variable that increases the permeability as the hydrostatic pressures increase.  This is why this test is only used to test mix designs in a laboratory. 
 

Through proper mix design and compressive strengths, one can deliver a low value of chloride ion penetration.  However, there is no test available that allows one to demonstrate the in place chloride ion resistance.  This testing is beyond the scope of the current ACI 318, which is the controlling document of most Building Codes and the IBC. 

Waterproofing is a required trade practice

WATERPROOFING is also required to protect concrete and it's steel reinforcement from sulfates, hydrogen sulfide and chloride degradation.  To prevent water from permeating through concrete basements and subterranean structures, waterproofing is oftentimes applied to the soils prior to the placement of reinforcement or to the outside of subterranean concrete structure prior to back-filling.   

Just because a swimming pool has water intentionally added to the interior of the structure, does that mean that we do not have a duty to protect the concrete from the permeation of water from BOTH sides of the structure?

Paolo Benedetti 
Aquatic Artist, Watershape Consultant, Expert Witness 
"Creating water as art."™ 
Aquatic Technology Pool and Spa 
©www.aquatictechnology.com